Get a quote

Free toolArea & cutting list

Glass Area & Cutting List Calculator

List your panes in mm and get the total glass area in m², the edge length for polishing and the price per m² of each quote you receive. Free cutting-list calculator.

Get a free quote

A glass processor in a workshop checking a large clear toughened panel with a drilled hole on a rack of cut panes
A glass processor in a workshop checking a large clear toughened panel with a drilled hole on a rack of cut panes

Glass is priced by the square metre, with edgework priced by the running metre. List each pane's width and height in millimetres and how many you need, and the calculator gives you the total area in m², the total edge length and the weight. When quotes arrive, enter their totals to see what each one works out to per square metre, so you compare like with like.

#Width (mm)Height (mm)Qtym²
1××–
2××–
3××–
4××–

– m² of glass

Panes
–
Edge length (polishing)
– m
Total weight
– kg
Largest pane
– m²

Compare your quotes

Enter each quote's total in rand to see its price per m². Check that they are for the same glass, edges, fittings and VAT first.

R
R
R

Copies the panes into the cutting list in the quote form below.

Get a free glass quote

Tell us what you need and where. A glass supplier or glazier who works in your area quotes you directly.

Request no.CL-65857

Cutting list (optional)

Know the sizes? List each pane in millimetres. Toughened glass can't be cut afterwards, so sizes help the glazier quote, but they will still measure up before ordering.

#Width (mm)Height (mm)Qty
1××
2××
3××
0 m²no panes yet
Thickness, if you know it
Tick what applies (optional)

Free and no obligation. By sending you agree that we may share your request with a suitable supplier or glazier. See our privacy policy.

How to measure for a cutting list

  • Measure in millimetres, width first, then height. Glaziers write sizes this way and it avoids mix-ups.
  • Measure the opening in three places and use the smallest figure. Walls and frames are rarely square.
  • Ask whether the size you give is the glass size or the opening size. For frameless glass the glazier deducts gaps for hinges, seals and silicone, usually a few millimetres each side.
  • Mark holes, notches and cut-outs on a sketch. Toughened glass cannot be cut or drilled afterwards, so every hole is made before toughening.

Most glaziers measure on site before ordering toughened glass, but your list gets you an accurate first price.

Area, edges and minimum charges

Area is width × height ÷ 1,000,000 for each pane, times the quantity. Edge length is the perimeter, 2 × (width + height), which is what polishing, bevelling or arrising is priced on. Many processors charge a minimum area per pane, often around 0.25 to 0.5 m², so very small pieces cost more per square metre than the calculator shows. Shapes and cut-outs are usually priced on the rectangle the shape is cut from.

Comparing quotes per square metre

Totals are hard to compare when one quote includes fitting, hardware and delivery and another is glass only. Dividing each total by the area gives a price per square metre you can set side by side, but only once you are sure the quotes are for the same thing: the same type and thickness, the same edge finish, the same fittings and whether VAT, delivery and installation are included. A lower rate for thinner glass or lighter hardware is not a saving.

Frequently asked questions

How do I convert mm to m²?
Multiply the width by the height in millimetres and divide by 1,000,000. A pane of 900 × 2,000 mm is 1,800,000 mm², which is 1.8 m².
Why does my quote show more m² than I measured?
Processors often round each pane up to a set increment or charge a minimum area per pane, and shapes are priced on the rectangle they are cut from. Ask how the area was worked out if it looks high.
Is edge polishing charged separately?
Often, yes. It is priced per running metre of edge, so long thin pieces such as shelves and splashbacks can have a lot of edge for their area. The calculator gives the total edge length to check against your quote.
Can I send this list with my quote request?
Yes. Press the button under the results and your panes are copied into the cutting list in the quote form below, which goes to the supplier or glazier with your request.

Guides and quotes for this job

More glass calculators

Get a free quote